Bathroom remodeling referrals for Tampa & nearby townsCall: (813) 536-3668
(813) 536-3668

Curbless and walk-in showers: what goes into them

bathroomremodeltampa.net

A walk-in shower looks simple, but the layout, drain and waterproofing decisions behind it are what make it work. This guide explains the code items, the slab question in Florida homes and what to ask a remodeler.

Need bathroom remodel help now?
Call now to be connected with a local bathroom remodeler in Tampa.
(813) 536-3668

A walk-in shower looks simple, but the layout, drain and waterproofing decisions behind it are what make it work. This guide explains the code items, the slab question in Florida homes and what to ask a remodeler.

Walk-in and curbless are not the same thing

People use the terms loosely, so it helps to separate them. A walk-in shower is any shower you enter without stepping over a tub wall, usually through a doorway or a glass opening. It may still have a low curb of a few inches that holds the water in. A curbless shower, sometimes called a zero-threshold or barrier-free shower, has a floor that continues from the bathroom into the shower with no raised edge, and the floor slopes to a drain instead.

Both suit homeowners who want an easier entry, a cleaner look or room for a bench or a mobility device. Both are also a bigger job than swapping a fiberglass insert. If you are comparing types of work, see the pages for walk-in shower installation and curbless shower installation.

Shower size and the code

The model plumbing code, IRC P2708.1, sets the minimum size for a shower compartment: at least 900 square inches of interior floor area, which works out to 30 by 30 inches, and the compartment has to hold that size from the finished floor to a height that clears the showerhead. For an open walk-in shower over 70 inches tall with no door or curtain, the same section calls for at least 36 inches in each direction. The code references we cite are secondary summaries of the model code, so confirm the edition and any local amendments with your permit office.

These are minimums. Most people want more elbow room than 30 inches, and a shower with a bench or a wheelchair-friendly layout needs far more. For reference only, the ADA's standard roll-in shower is 30 by 60 inches with 30 by 60 inches clear in front, and a transfer shower is 36 by 36 inches. Those numbers are not required in a private home, but they show how a room scales when mobility is a priority. See our aging in place guide for more on that planning.

Glass, safety glazing and open designs

Glass near a shower is treated as a hazardous location. Under IRC R308.4.5, glass next to a tub or shower must be safety glazing, such as tempered glass, when its bottom edge is less than 60 inches above the standing surface and within 60 inches horizontally of the tub or shower. That covers shower doors, fixed panels, and also windows near the water. The usual answer is tempered or laminated glass, and the label is etched in a corner.

Walk-in showers often use a fixed glass panel and no door. That reduces hardware and cleaning, but the open side means water can reach the floor, so the design needs the right panel width, the right slope and a showerhead aimed away from the opening. A shower door installation is a separate trade step from tile, and glass is usually ordered after the tile is set and the walls are measured, which can add time to the schedule. In Tampa Bay, hard water spots on glass are a common complaint, so ask about coatings and squeegee habits.

The slab, the recess and the drain

This is the part of a curbless shower that surprises people. To keep a flat transition, the shower floor needs to sit lower than the bathroom floor so that it can slope toward the drain. There are only a few ways to get that drop:

  • Recess the shower area in a wood-framed floor by lowering the joists or notching them, which takes structural care.
  • Cut and lower a section of a concrete slab, which many Tampa Bay houses have. This means saw-cutting, breaking out concrete, reworking the drain line and patching, so it is noisy, dusty and one of the costlier parts of the job.
  • Raise the bathroom floor outside the shower slightly with a thin buildup, which can create a small change at the door.
  • Use a pre-sloped foam or composite shower base that lets the pan drop only a little.

Which one fits depends on your house. A 1960s block home in Pinellas, a 1920s bungalow on pier foundations in Tampa and a newer slab house in Riverview will each take a different approach, and a remodeler should look at the floor before promising a method. If the drain has to move, the plumber is working under the floor, so ask whether the existing waste line is in good shape.

Drains come in two broad types. A center point drain has a single slope to the middle. A linear drain runs along one edge or wall, which allows a single-plane slope and lets you use larger tile. Either one is a plumbing item, and your remodeler must be able to tell you how it will connect to the waste line.

Waterproofing, tile and slope

The invisible layers decide whether a curbless shower lasts. The shower floor needs a continuous waterproof membrane that is tested before tile goes down, usually by plugging the drain and flooding the pan for a set time. Because there is no curb to hold water in, the slope, usually a quarter inch per foot, is the main defense, and the membrane often runs up the walls and across the bathroom floor near the opening.

The tile you choose also matters. Small mosaic tiles follow a slope easily and add grip. Large-format tile looks clean but needs a precise slope, or a linear drain with a single plane. Our tile and flooring choices guide covers the trade-offs, and bathroom tile installation is the trade step at the end of the build. Tile itself does not need a state license according to DBPR, but the plumbing under it does.

In Florida's humidity, a shower with no curb or door also needs good ventilation. The IRC calls for an exhaust fan of at least 50 cfm if it runs intermittently or 20 cfm if continuous, unless there is a compliant window. Read the humidity and ventilation guide before you finalize the fan.

Permits and inspections

Changing the drain, the supply lines or the slab usually calls for a permit, and the building office inspects plumbing before it is covered. The details differ between City of Tampa, Hillsborough County and the other cities in our service area. Our bathroom permit guide explains how to find the right office and what to ask. Plumbing work must be done by someone who holds a Florida plumbing contractor license, which you can look up on DBPR's licensee search at MyFloridaLicense.com. If your home is in a flood zone, ask about the 50 percent substantial-improvement threshold in the flood zone guide.

Questions to ask a remodeler

  1. How will you create the drop for the floor, and what does it mean for my slab or framing?
  2. Which drain type do you recommend, and why?
  3. How is the membrane tested before tile is set?
  4. Where will the glass or fixed panel go, and when is it ordered?
  5. What will be permitted, and who pulls the permit?

When your questions are ready, call the number on this page to be connected with a local bathroom remodeler.

Call now to be connected with a local bathroom remodeler in Tampa.
(813) 536-3668

Bathroom Remodel Tampa is a referral service, not a remodeling company, so scope and pricing come from the remodeler you speak to. For a look at the project in order, read how long a bathroom remodel takes.

Frequently asked questions

What is the minimum size for a shower?
The model code cited here, IRC P2708.1, calls for at least 900 square inches of interior floor area (30 by 30 inches). An open walk-in shower over 70 inches tall with no door or curtain needs at least 36 inches in each direction. Confirm the adopted edition with your permit office.
Does shower glass have to be tempered?
Under IRC R308.4.5, glass next to a tub or shower is a hazardous location when its bottom edge is under 60 inches above the standing surface and within 60 inches horizontally, so it must be safety glazing such as tempered glass.
Can a curbless shower be built on a concrete slab?
Often yes, but the slab may need to be cut and recessed so the shower floor can slope to the drain. That is a plumbing and concrete job, so ask the remodeler how they would handle your floor.
What is the difference between a linear drain and a center drain?
A center drain sits in the middle of the shower floor, with slopes toward it. A linear drain runs along an edge, which allows a single slope and can suit larger tile. Both connect to the waste line, and either can work with the right slope.
Call now to be connected with a local bathroom remodeler in Tampa.
(813) 536-3668

Last updated:

☎ Call (813) 536-3668